SLITTERS
|
|
|
|
|
|
|
|
|
|
|
|
|
Sheet Metal SLITTING MACHINES
A+ Rating
Click to request a quote or call 773-334-5000
to order a machine.
Looking for a low
cost machine to quickly cut lots of long sheet metal pieces? Well look
no further. A sheet metal slitter machine will cut up to any length
of material you want. When your metal comes from sheet stock, a Gary
slitter will be a great addition to your shop for fast cutting needs.
Available in single cut or multi-cut. If you cant afford to buy a Gary,
we offer the less expensive Tin Knocker brand.
GARY
single cut Slitter
Sturdy
24 inch throat slitter with quick adjusting back gauge and scale.
Click
to request a quote for this machine
Die-set type gauge mounting that insures easy setting and consistent
squareness.
Gauge mounting rods are extended to provide convenient carrying
handles.
Gauge is easily removed for machine transport and re-installed
with no resquaring.
Slitter knives are proven GARY "quickset" design manufactured
from tool steel.
Knives are outboard mounted for easy access knives are reversible
, intervals between sharpening is double that of a single edge knives.
"Adiprene" stripper rings are non-marking and serve to hold
the material flat reducing twist.
Dual bearings mounted at knife end to minimize deflection
and increase knife life.
Heavy duty roller chain drive with by 1/3 HP gearmotor.
Standard 110 volt with grounded plug. 6 amps.
Options: Stand, extra Knives, Stripper Rings |
GARY
3354 Rotary Slitter |
Capacity:
16 Gauge (.06") |
Throat:
24" |
Motor:
1/3 HP, 110 volts |
Minimum
Slitting Width: 1" |
Maximum
Slitting Width: 24" |
Shipping
Weight: 450 Lbs. |
|
Sheet fed multiple
cut Slitting machines
GARY 3350DX
multi-cut Gang Slitter
Click
to request a formal quote for this machine
* This machine can slit 4 foot wide sheet metal into 3 or 4 pieces
in one pass.
* With the right knives and strippers you can slit different sheet
metals, wire screen, fiberglass screen, gasket materials, cork,
foam rubber, polystyrene, plastic and formica.
* 3" diameter cold - roll turned, ground and polished shafts mounted
in dual wall ball bearings lubricated for life.
* Gauge mounted on each side for left or right hand use.
* End frames are aluminum - magnesium alloy.
* Rugged lightweight GARY torsion tube assembly.
* Heavy gauge steel with "T" bar reinforcement.
* Slitter knives are proven GARY "quickset" design manufactured
from tool steel.
* Knives are "reversible", intervals between sharpening is double
that of a single edge knives.
* 2 sets of standard 3" X 5" X 3/4" wide high-carbon tooling is
included.
* 60 feet per minute standard operating speed.
* Heavy duty roller chain drive powered by 3/4 HP gearmotor. Variable
speed is optional.
* Electricity: Choose 110 volts 1 phase
or optional 240v 3 phase or 480 volts 3 phase.
* Maximum sheet width: 49"
* Cutting rate: 40 feet per minute
* Machine weight: 480 Lbs.
|
Maximum
number of simultaneous cuts:
30 gauge (.015") metal: 12 cuts
28 gauge (.018") metal: 8 cuts
26 gauge (.021") metal: 6 cuts
24 gauge (.024") metal: 4 cuts
22 gauge (.031") metal: 3 cuts
20 gauge (.036") metal: 2 cuts
18 gauge (.048") metal: 2 cuts
16 gauge (.060") metal: 1 cut
|
Tin Knocker
multi-cut Gang Slitter
Click
to request a formal quote for this machine
This machine can make multiple cuts in one pass.
Great machine for roofing company.
Gang slit blanks from 16 gauge to 30 gauge.
Gang slit galvanized sheet metal, copper, pre-painted metals
and other materials.
FEATURES:
2 sets of reversible cutting knives.
Tool steel blades with stripper rings.
Stripper fingers to prevent twist.
Optional third set of knives available.
Heavy duty chain drive.
Bearings lubricated for life.
SPECIIFCATIONS:
Maximum Cutting Width: 48-1/2 inches
Width between end frames: 52 inches
Feed Speed: 60 Feet Per Minute
Electrics: 1 phase, 110 or 220 Volts
Motor: 3/4 HorsePower
3 inch diameter polished steel shafts
Knife Sizes: 3 inch I.D. x 5 inch O.D. x ¼ thick
Table Height: 35 inches
Shipping Weight: 525 Lbs.
Ship Dimensions: 67 x 37 x 48 inches
|
|
|